Attenuator 3 dB 10 GHz 50 Ω SMA (m-f)

The Pico TA181 3 dB RF Attenuator is a compact fixed attenuator designed to reduce RF signal power by a nominal 3 dB while maintaining a controlled 50 Ω transmission environment.

It operates across a wide frequency range from DC to 10 GHz, making it suitable for RF laboratories, microwave test benches, electronics development, production testing and measurement-system integration.

A 3 dB attenuation corresponds to approximately half the signal power at the output compared with the input under ideal matched conditions. The voltage amplitude across equal impedances is reduced to approximately 70.7% of the original value.

The TA181 uses an SMA male connector on one end and SMA female connector on the other, allowing it to be inserted directly between compatible RF cables, instruments or devices without requiring an additional adaptor.

DC to 10 GHz Frequency Range

The TA181 is designed for operation from DC through 10 GHz.

This broad operating range makes it useful with:

• Vector network analyzers
• RF signal generators
• RF and microwave receivers
• Spectrum analyzers
• High-bandwidth oscilloscopes
• RF amplifiers
• Filters
• Antenna test setups
• RF development boards
• Communication test equipment
• Calibration and measurement systems

The same attenuator can therefore be used across low-frequency, RF and microwave measurements without changing components when the test frequency moves through different bands.

Fixed 3 dB Attenuation

The TA181 provides nominal 3 dB attenuation.

Fixed attenuation can be useful when a test setup requires predictable signal-level reduction without active circuitry or external power.

Typical uses include reducing signal levels before sensitive test equipment, controlling source power, improving measurement setup matching and preventing excessive drive levels from reaching downstream RF components.

Controlled Attenuation Accuracy

Pico specifies attenuation deviation according to operating frequency.

For the TA181 series, the maximum attenuation deviation is:

• ±0.2 dB from DC to 2 GHz
• ±0.3 dB from 2 GHz to 5 GHz
• ±0.5 dB from 5 GHz to 10 GHz

This means the actual attenuation remains close to the nominal 3 dB value throughout the stated operating frequency range.

For example, the expected attenuation range is approximately 2.8 to 3.2 dB from DC to 2 GHz and approximately 2.5 to 3.5 dB at the upper end of the 10 GHz operating range.

Low VSWR Performance

Good impedance matching is important in RF measurement systems because excessive reflections can affect amplitude accuracy and measurement repeatability.

Pico specifies the following maximum VSWR:

• ≤1.10 from DC to 2 GHz
• ≤1.25 from 2 GHz to 5 GHz
• ≤1.35 from 5 GHz to 10 GHz

The controlled VSWR helps minimise unwanted reflections when the attenuator is used in a properly terminated 50 Ω system.

50 Ω RF System Compatibility

The TA181 is designed specifically for 50 Ω RF systems, which is the standard impedance used by a wide range of laboratory and communication equipment.

It can be integrated with compatible:

• RF cables
• Network analyzers
• Spectrum analyzers
• Signal generators
• RF receivers
• Oscilloscopes with 50 Ω inputs
• RF amplifiers
• Test fixtures
• Measurement accessories

Using components with consistent 50 Ω impedance helps reduce reflections and measurement uncertainty in RF signal paths.

2 W Power Handling

The TA181 is rated for 2 W RF power handling.

This makes it suitable for low-to-moderate power RF laboratory applications, including source-level reduction, receiver protection and general test-system signal conditioning.

The applied RF power should remain within the manufacturer's specified rating to prevent excessive heating or damage to the attenuator.

SMA Male-to-Female Connection

The attenuator uses:

• SMA male input/output interface on one side
• SMA female interface on the opposite side

The male-to-female configuration allows direct inline installation between SMA-connected equipment.

Typical arrangements include:

RF source → TA181 attenuator → measurement instrument

or

Device under test → TA181 attenuator → analyzer

The inline design reduces the need for additional RF adapters, which can otherwise introduce additional insertion loss, reflections and connection uncertainty.

Passive Operation

The TA181 is a completely passive RF component.

It requires:

• No external power supply
• No software
• No calibration setup for operation
• No active control circuitry

This makes it simple to integrate into laboratory and production-test setups where a fixed and repeatable reduction in RF signal level is required.

RF Measurement Equipment Protection

A fixed attenuator can provide an additional level of signal reduction before the input of sensitive measurement equipment.

It may be used ahead of:

• Vector network analyzer receivers
• Oscilloscope inputs
• Spectrum analyzers
• RF receivers
• Measurement modules

The attenuator should not be treated as a substitute for verifying the maximum input rating of connected equipment. Engineers should always ensure that the signal remaining after attenuation is within the safe operating limits of the instrument.

Improving Measurement Setup Matching

RF attenuators are often placed between a source and load to improve the effective impedance environment of a measurement setup.

The TA181 can help reduce the influence of reflections between connected RF devices, particularly where source or load impedance is not perfectly matched to 50 Ω.

This can improve repeatability in:

• VNA measurements
• RF amplifier testing
• Filter characterization
• Return-loss measurements
• Signal-generator setups
• Receiver sensitivity testing

The degree of improvement depends on the complete RF signal path and the characteristics of the connected equipment.

Cascaded Attenuation

Multiple fixed attenuators may be connected in series when a higher total attenuation value is required, provided that power, connector and measurement requirements are satisfied.

Pico also offers related 10 GHz fixed attenuators in the same family:

This allows engineers to select or combine attenuation values according to the required RF signal level.

Applications

The Pico TA181 can be used for RF and microwave applications including signal-level adjustment, VNA measurements, RF amplifier testing, filter characterization, spectrum-analysis setups, signal-generator output conditioning, receiver testing, impedance-matching improvement, laboratory RF measurements, production-test systems, educational RF laboratories and general 50 Ω signal-path conditioning.

Why Buy from RevineTech?

RevineTech supplies Pico Technology RF products and test accessories for electronics development, RF laboratories, research, education and production testing.

Technical selection support can help users choose the appropriate fixed attenuator, RF cable, adaptor, calibration accessory or VNA configuration according to operating frequency, connector type, attenuation requirement and measurement setup.